為了防止泰州INA軸承金屬表面被水腐蝕,，須對機床進行充分的潤滑,，并對機床的重要部件進行潤滑。

In order to prevent the metal su-ce of INA bearing in Taizhou from being corroded by water, it is necessary to lubricate the machine tool adequately and lubricate the important parts of the machine tool.

當泰州INA軸承機器停止工作時,，用切削液清洗機器表面,，打開機器的保護蓋，以分散機器工作區域內的潮濕空氣,。為防止電蝕的發生,，應在金屬表面涂覆一層防水油脂。這是不夠的,，以加強機床接地,。為了避免的滋生和繁殖，應定期清洗或更換切削液,，及時去除切屑,，用軟水（低礦物含量的純水）稀釋濃縮切削液。

When Taizhou INA bearing machine stops working, clean the machine su-ce with cutting fluid and open the protective cover of the machine to disperse the moist air in the working area of the machine. To prevent the occurrence of electric erosion, a layer of waterproof grease should be coated on the metal su-ce. This is not enough to enhance the grounding of machine tools. In order to avoid breeding and reproduction, cutting fluid should be cleaned or replaced regularly, chips should be removed in time, and cutting fluid should be diluted and concentrated with soft water (pure water with low mineral content).

除了泰州INA軸承的質量太硬,，還屬于非常密的部件,，這兩種高性能的軸承，如果使用不當,，不但不能達到預期的性能,，而且容易損壞軸承，須注意潤滑,。

In addition to Taizhou INA bearing quality is too hard, but also belongs to very dense components, these two high-performance bearings, if used improperly, not only can not achieve the desired performance, but also easy to damage the bearings, we must pay attention to lubrication.

在使用和安裝時,，應注意不要有強烈的沖擊力，不要有垂直連接的絲錐軸承,，不要讓壓力通過滾動元件,。

When using and installing, care should be taken not to have strong impact force, no vertically connected taper bearings, and no pressure passing through rolling elements.

使用泰州INA軸承適當準確的安裝工具，盡量使用專用工具，盡量避免使用布料和短纖維等物品,。

Use appropriate and accurate installation tools for Taizhou INA bearings, use special tools as far as possible, and avoid using cloth and staple fibers as far as possible.

保持軸承及其周圍環境盡可能清潔,。即使不可見的微笑灰塵進入軸承，它也會增加軸承的磨損,、振動和噪音,。

Keep bearings and their surroundings as clean as possible. Even if the invisible smile dust enters the bearing, it will increase the wear, vibration and noise of the bearing.

防止軸承腐蝕

Preventing bearing corrosion

當用手直接取出泰州INA軸承時，須徹底清洗手上的液體,，并在操作前涂上高質量的礦物油,。在雨季和夏季，應特別注意防銹,。在一定條件下,，軸承的壽命比傳統軸承的壽命長，特別是在輕載條件下,。這些特殊的操作條件是,，當滾動表面（軌道和滾動部件）被潤滑油膜分離時，污染物可能引起表面損傷,。事實上,，在理想條件下，所謂的軸承壽命是可能的,。

When taking out Taizhou INA bearing directly by hand, the liquid on the hand should be thoroughly cleaned and high quality mineral oil should be coated before operation. In the rainy season and summer, special attention should be paid to rust prevention. Under certain conditions, the life of bearings is longer than that of traditional bearings, especially under light load conditions. These special operating conditions are that contaminants may cause su-ce damage when the rolling su-ce (track and rolling parts) is separated by lubricating oil film. In fact, under ideal conditions, the so-called bearing life is possible.

文章來自：泰州SKF軸承 www.wh-skf.com

The article is from: Taizhou SKF bearing www.wh-skf.com

文章來自：泰州INA軸承 www.ina-china.cn

The article is from: Taizhou INA bearing www.ina-china.cn

文章來自：泰州NSK軸承 www.klbbearings.com

The article is from: Taizhou NSK bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672