為了充分觀察機器的定期檢查和更換,并拆下軸承,檢查滾道表面狀況和是否沒有損壞,是否可以重復使用,見第5項:進口軸承的檢查.運行中的檢查項目包括INA軸承的滾動聲,、振動,、溫度和潤滑狀況.具體如下:在運行中發現異常情況時.

In order to fully observe the regular inspection and replacement of the machine, and remove the bearings, check the raceway su-ce condition and whether there is no damage, whether it can be reused, see item 5: inspection of imported bearings. Inspection items in operation include rolling sound, vibration, temperature and lubrication of INA bearings. Specifically as follows: when abnormal conditions are found in operation.

通過麥克風檢查軸承的滾動聲音.即使進口軸承有輕微的剝落損傷,也會產生不正常,、不規則的聲音,可以用麥克風分辨.

Check the rolling sound of the bearing through the microphone. Even if the imported bearing has slight peeling damage, it will produce abnormal and irregular sound, which can be distinguished by microphone.

軸承振動對軸承的剝落,、壓痕,、生銹,、裂紋,、磨損等損傷非常min感,在軸承振動測量中可以反映出來.因此,可以使用專用的軸承振動測量裝置(頻率分析儀等)來測量振動,不能從頻率中推斷出異常情況.根據INA軸承的工作情況或傳感器的安裝位置,測量值從今天到今天都有變化,因此在確定判斷標準之前,有必要對每臺機器的測量值進行分析比較.

Bearing vibration is very sensitive to the damage of bearing such as spalling, indentation, rust, crack and wear, which can be reflected in bearing vibration measurement. Therefore, the special bearing vibration measuring device (frequency analyzer, etc.) can be used to measure vibration, and the abnormal situation can not be inferred from the frequency. According to the working condition of INA bearings or the installation position of sensors, the measured values vary from today to today, so it is necessary to analyze and compare the measured values of each machine before determining the judgment criteria.

進口軸承的溫度可以從軸承外部的溫度獲得.如果油孔能直接測量軸承外圈的溫度,則更為合適.通常情況下,軸承的溫度隨著運行開始緩慢上升,1-2小時后達到穩定狀態.軸承室溫度隨機化器的熱容量,、散熱量,、轉速和負荷不同.如果潤滑和安裝部件合適,軸承溫度將急劇上升,并出現異常高溫.這時,我們須停止工作,采取必要的預防措施.根據大量試驗數據,本表列出了各種INA軸承外圈的平均溫度,供參考.

The temperature of the imported bearing can be obtained from the temperature outside the bearing. If the oil hole can directly measure the temperature of the bearing outer ring, it is more suitable. Usually, the temperature of the bearing rises slowly with the start of operation and reaches a stable state after 1-2 hours. The heat capacity, heat dissipation, rotational speed and load of bearing chamber temperature randomizer are different. If the lubrication and installation parts are suitable, the bearing temperature will rise sharply and abnormal high temperature will occur. At this time, we must stop working and take necessary precautions. According to a large number of test data, the average temperature of various INA bearing outer rings is listed in this table for reference.

軸承潤滑對滾動軸承的疲勞壽命、摩擦,、磨損,、溫升和振動起著重要作用.沒有正常潤滑,軸承就不能工作.對軸承損壞原因的分析表明,約40個百分比的軸承損壞與潤滑bu良有關.因此,良好的軸承潤滑是降低軸承摩擦磨損的you效措施.此外,軸承的潤滑還具有散熱,、防銹、密封和減震等功能.軸承的潤滑可簡單描述如下:

Bearing lubrication plays an important role in the fatigue life, friction, wear, temperature rise and vibration of rolling bearings. Bearings cannot work without normal lubrication. The analysis of the causes of bearing damage shows that about 40% of bearing damage is related to good lubrication bu. Therefore, good bearing lubrication is a youeffect measure to reduce bearing friction and wear. In addition, the lubrication of bearings also has the functions of heat dissipation, rust prevention, sealing and shock absorption. The lubrication of bearings can be simply described as follows:

a.在兩個滾動或滑動表面之間形成油膜,分離兩個表面,減少接觸表面的摩擦和磨損.

A. Forming oil film between two rolling or sliding su-ces, separating the two su-ces, reducing friction and wear on the contact su-ce.

b.使用INA軸承油潤滑時,特別是使用循環油潤滑,、油霧潤滑和噴油潤滑時,潤滑油可以帶走軸承的大部摩擦熱,起到散熱的作用.

B. When using INA bearing oil lubrication, especially when using circulating oil lubrication, oil mist lubrication and oil injection lubrication, the lubricant can take away most of the friction heat of the bearing and play the role of heat dissipation.

c.油脂潤滑可防止灰塵等異物進入軸承,起到密封作用.

C. Grease lubrication can prevent foreign matter such as dust from entering the bearing and play a sealing role.

文章來自:SKF軸承 -

Article from: SKF Bearing -

文章來自:INA軸承 -

Articles from: INA Bearing -

文章來自:NSK軸承

Article from: NSK Bearing

QQ:

電話:0

手機:/